SPECIAL APPLICATIONS / INDUSTRIAL – Chromodomi

BLEND PRIMER

softways — Mon, 12 May 2025 04:59:13 +0000

To ensure proper adhesion of the paint have to the surface be cleaned from dust, grease, oil, peeling old paint, rust, mold or moisture etc. Sand the surface and remove sanding residue with a rag. Add part B to part A, mix by volume rate 2:1 and stir to obtain a uniform mixture (2-3 minutes).Stir well before use. Do not apply at temperatures below 6°C and above 40°C and at relative humidity above 80%. Apply the blend primer 1-2 coats and let it dry for 1 hour. Recoated after 2-4 hours.

Attention: If we mix components A and B the product can’t be stored for future use.

POLYLAC 2K

softways — Fri, 09 May 2025 09:48:50 +0000

APPLICATION

To ensure proper adhesion of the paint have to the surface be cleaned from dust, grease, oil, peeling old paint, rust, mold or moisture, and then primed with undercoat which recommended depending on the surface. Stir well before use. Do not apply at temperatures below 6°C and above 40°C and at relative humidity above 80%. Add part B to part A, mix by volume rate 1:2 per weight and stir to obtain a uniform mixture (2-3 minutes). Apply 1-2 coats of paint and allow to dry for 1-2 hours. Recoated after 12 hours.
Attention: If we mix components A and B the product can^27t be stored for future use.

POOL PAINT EPOXY PAINT 2K

softways — Fri, 09 May 2025 05:11:53 +0000

SURFACE PREPARATION
To ensure proper adhesion of the product have to the surface be cleaned from dust, grease, oil, peeling old paint, rust, mold or moisture.
Mix the components A and B in a ratio 4:1 by volume stirring continously.
Dilute the mixture if needed with epoxy primer up to 5%
The mixture can be used for about 24 hours.
The product has all the mechanical strength after 20-30 days

Attention: If we mix components A and B the product can’t be stored for future use.

APPLICATION CONDITIONS
Do not apply at temperatures below 6°C and above 40°C and at relative humidity above 80%. Adverse conditions in the application can alter the final properties of product.
During working keep tools “liquid” in the container or the container with the product. Drain well the product of the tools back in the box and clean immediately with epoxy thinner. If product dries only with strong detergents. Do not empty washings into the groundwater.

EPOXY VARNISH 2K- WATER

softways — Fri, 09 May 2025 04:38:54 +0000

SURFACE PREPARATION

To ensure proper adhesion of the product, the painted surface must be cleaned of dust, grease, oil, peeled old paint, rust, mold or moisture residue.
Mix component A and B with a low speed stirrer for 2-3 minutes. Leave the mixture and then repeat the stirring. The entire amount of A with B component must be stirred in the proportion given.
If a smaller amount is to be applied then the ingredients need to be weighed in the same weight ratio, at a ratio of 3: 1 by volume with good agitation.
Dilute the product with water at a rate of 5-10% for the desired workability
Applied in one or two coats on dry, clean surfaces free of dust, loose and loose particles which prevent the product from sticking
The product acquires all its mechanical strength after 20 – 30 days.

Caution: if we mix component A and B the product can not be stored and reused.

Avoid applying the product at temperatures below 6 ° C and above 40 ° C and when the relative humidity is greater than 80%. Adverse conditions during application may alter the final properties of the product.
CAUTION: Wear protective gloves / protective clothing / eye / face protection. In case of contact with eyes, rinse thoroughly with plenty of water for several minutes. If there are contact lenses, remove them if they are easy. Keep rinsing.
Immediately call the POISON CENTER or your doctor

COVER LUX INDUSTRIAL METAL ENAMEL & PRIMER

softways — Thu, 08 May 2025 13:03:05 +0000

APPLICATION CONDITIONS
Do not apply at temperatures below 6°C and above 40°C and at relative humidity above 80%. Adverse conditions in the application can alter the final properties of product.
During working keep tools “liquid” in the container or the container with the color. Drain well the color of the tools back in the box and clean immediately with white spirit or nitro thinner. If paint dries only with strong detergents. Do not empty washings into the groundwater.

EPOXY VARNISH 2K

softways — Thu, 08 May 2025 11:04:00 +0000

SURFACE PREPARATION
To ensure proper adhesion of the product, the surface to be painted must be cleaned of dust, grease, oil, peeled old paint, rust, mould or moisture residues.
Mix component A and B in a ratio of 4:1 by volume with good stirring.
Dilute the product with epoxy solvent at 5%.
The product gains all its mechanical strength after 20 – 30 days.

Caution: if you mix component A and B, the product cannot be stored and reused.

APPLICATION CONDITIONS
void applying the product at temperatures below 6°C and above 35°C and when the relative humidity is above 70% or if there is a possibility of rain or frost in the next 48 hours.Adverse conditions and not following the application instructions may alter the final properties of the product.
During working keep tools “liquid” in the container. Drain well the product of the tools back in the box and clean immediately with warm water and soap. If product dries, clean only with strong detergents. Do not empty washings into the groundwater.
WARNING: Wear protective gloves/protective clothing/personal protective equipment for eyes/face.In case of contact with eyes, rinse carefully with plenty of water for several minutes. If contact lenses are present, remove them if possible. Continue to rinse.

PRIMER FOR GALVANIZED SURFACES

softways — Thu, 08 May 2025 09:50:02 +0000

SURFACE PREPARATION
To ensure proper adhesion of the product have to the surface be cleaned from dust, grease, oil, peeling old paint, rust, mold or moisture.
For new, freshly galvanized surfaces require good scrubbing.
After surface preparation apply one coat of primer galvanized.
When it dries,we sand and clean the surface making it ready for the topcoat.
The product has all the mechanical strength after 20-30 days
APPLICATION CONDITIONS
Do not apply at temperatures below 6°C and above 40°C and at relative humidity above 80%. Adverse conditions in the application can alter the final properties of product.
During working keep tools “liquid” in the container or the container with the product. Drain well the product of the tools back in the box and clean immediately with nitro solvent. If product dries only with strong detergents. Do not empty washings into the groundwater

EPOXY PAINT 2K

softways — Thu, 08 May 2025 09:38:52 +0000

SURFACE PREPARATION
To ensure proper adhesion of the product have to the surface be cleaned from dust, grease, oil, peeling old paint, rust, mold or moisture.
Mix the components A and B in a ratio 4:1 by volume stirring continously.
Dilute the mixture with epoxy thinner up to 5%
Apply a coat of the product. If you want to increase the adhesion of the coating, add quartz sand at a rate of 10-20% by weight.
The mixture can be used for about 24 hours.
The product has all the mechanical strength after 20-30 days

Attention: If we mix components A and B the product can^27t be stored for future use.

ROAD PAINT

softways — Thu, 08 May 2025 09:31:14 +0000

SURFACE PREPARATION
To ensure proper adhesion of the paint have to the surface be cleaned from dust, grease, oil, peeling old paint, rust, mold or moisture.
Stir well the product and apply.
The product has all the mechanical strength after 20-30 days
APPLICATION CONDITIONS
Do not apply at temperatures below 6°C and above 40°C and at relative humidity above 80%. Adverse conditions in the application can alter the final properties of product.
During working keep tools “liquid” in the container or the container with the color. Drain well the color of the tools back in the box and clean immediately with nitro thinner. If paint dries only with strong detergents. Do not empty washings into the groundwater.

METALL FARBE

softways — Thu, 08 May 2025 09:27:08 +0000

SURFACE PREPARATION
To ensure proper adhesion of the paint have to the surface be cleaned from dust, grease, oil, peeling old paint, rust, mold or moisture.
Apply to the surface the recommended primer. (primer fast-drying)
Stir well the product and apply on 2 coats every 4 hours.
The product has all the mechanical strength after 20-30 days
APPLICATION CONDITIONS
Do not apply at temperatures below 6°C and above 40°C and at relative humidity above 80%. Adverse conditions in the application can alter the final properties of product.
During working keep tools “liquid” in the container or the container with the color. Drain well the color of the tools back in the box and clean immediately with nitro thinner. If paint dries only with strong detergents. Do not empty washings into the groundwater.